Home » » No Cracked Orginal Setup File-Cyclone Box - Download - Installation - First Steps

No Cracked Orginal Setup File-Cyclone Box - Download - Installation - First Steps

(Updated 07.07.2010 - )


1. Download final installer from: http://www.karwos.hk/CycloneBoxInstaller.exe and Install it. While installing agree to install box drivers, etc.

2. Connect box to PC. PC should detect new device - "Cyclone Bootloader". Simply do automatic driver installation, till installer installed them in Win32 INF already.

3. Run Start -> Programs -> Cyclone Box -> Cyclone Box



At bottom, you should see "Connected [Bootloader Mode]". That means your box was detected by software, and you can proceed with box registration - needed step to activate your box.

4. Run Box Registration Wizard, click Prepare Box.



Select your reseller from list, and fill all needed data.



If you see "Box registration status: Registered OK" that means all passed ok. You can proceed with box activation.

5. Run Box Maintenance Wizard, and click Maintenance box. In 1-2 minutes your box will be initialized.

**** VERY IMPORTANT : During box upgrade, please DON'T disconnect your box, even if software may act as hang ! We use ciphering on few layers during upgrade, and if you have slower PC, decrypting RSA and other ciphers, may take quite more time !! And then, if you disconnect your box, it will not be upgraded. It is no problem, because it will not be damaged, but You will lose YOUR time and OURS time, asking for next update credit !!



6. Your box is registered and activated. Now your security card needs be initialized. To initialize security card, box needs be activated! Run Security Card Manager. Read your card, and click Fill Credits. Box should change its mode to Cyclone Box and Windows should install new drivers again (same steps as for Bootloader). On bottom of screen you should see "Connected [Main Mode]".



8. All is done. You can run DCT4/WD2/BB5 tool and check if necessary selftests will be passsed, so you can enjoy using your Cyclone Box One note: security card having 1000 credits at initialization. Each card operation tooks those credits, so after some time you need to reinitialize card (when counter reachs 0). This operation is of course free and realtime, using server.



Code:
Nokia DCT4/WD2/BB5 Service Tool Initialization Started, Engine Revision: 1.0.0.9912
Handling device: [Cyclone Team], [Cyclone Box]
Initializing box...
Box Firmware: Cyclone Nokia Application v01.45, (Jul  6 2010 19:20:51, gcc v4.3.2, RTOS V6.0.1), Type: Signed Production Application, (C) KarwosSoft 2010 wk27
Box Serial Number: C0000005
HW Revision: A, Suitable for: Production, Case: First Plastic Case, MCU Manufacture Time: 2008, wk32
Initializing security card...
Card Serial Number: D0000001
Card Firmware Revision: 0108
Card is activated
Box is activated
Started box selftests procedure
USB Voltage    4,99v    PASSED
MCU Voltage    3,30v    PASSED
Core Voltage    1,79v    PASSED
VBAT Voltage    0,01v    PASSED
VBAT Voltage    4,73v    PASSED
Box VPP disabled
VPP Voltage    0,02v    PASSED
Internal Box VPP Enabled
VPP Voltage    4,88v    PASSED
Box VPP disabled
VPP Voltage    0,00v    PASSED
External Box VPP Enabled
VPP Voltage    0,04v    FAILED - IGNORED - Probably power supply is not connected
Box VPP disabled
All box selftests passed!
Super DCT4 Activation: TRUE
Initializing FBUS...
All initialized - Ready to work
Remember to check the Version of the software and the firmware of your Cyclone box

Enjoy your box!


0 comments:

Post a Comment

অনলাইন থেকে আয় করুন

Popular Posts

All Mobile Flash File Stock Here

Cellular Flash File

Raeno Flash File

Rangs Flash File

AG-TEL Factory File

Walton Flash File

Ads 468x60px

by2 Flash File

icell Flash File

SMILE Flash File

Wootel Flash File

BeeFone Flash File

Hardware Solution